Mauser K98k (Bulb)

Sub Categories

Repeatable Mounts

Pivot Mounts

About the Mauser

Back in 1811, Friedrich I of Wurttemberg launched an arms factory in Oberndorf, Germany. Employing 133 workers, the company officially started its business in the following year serving as the royal weapon forge. The initial moderate success of the company was refined in 1867 when Wilhelm and Paul Mauser came up with an innovative rotating bolt system used for breechloading rifles. Most of their rifles at the time were built around a 7.9x57J cartridge which eventually became known as the 8mm German cartridge.

Alongside the Model 93 release, the smaller, 7x57mm cartridge was introduced. The United States spotted the potential of German ingenuity; hence they incorporated many features of Mauser design into their 1903 Springfield and so did the United Kingdom with their SMLE rifle that was the standard of British infantry units up until the 1950s. Soon after, many countries around the world, such as Turkey, Brazil, South Africa, Iran, Sweden and even China had recognised the outstanding performance of Mauser 93 and began flooding the company with new orders.

Along with their rifle production success, Mauser also broke new ground in 1896 with the introduction of their autoloading C96 pistol that was produced up until 1936. In 1897 the Mauser family were given control over the factory and renamed it Waffenfabrik Mauser AG. Only a year later, one of the most recognisable Mauser rifles of all time was presented by the company – Mauser Gewehr 98. The rifle had been redesigned with some of the noticeable changes being better-ruptured case gas venting, a stronger receiver with a larger receiver ring and an extra third locking lug providing additional safety. In later years, numerous rifles were derived from the original Gewehr 98 design, a lot of them being manufactured by various German contractors.

In the first decades of the 20th century, Mauser introduced a myriad of hunting rifles such as Type A, Model B, Model K, Armee-Model C and Africa Model. Up until the 1960s, various other models were presented including M1916, Mauser 1925 Special range, Karabiner K98, Mauser KKW cadet rifle, Gewehr 41 etc. Alongside their rifle production, the company additionally focused on the production of hand and pocket pistols, with some of the most recognizable models being Mauser 1910, Mauser 1914, Model 1934, and Mauser HSc.

After World War II, when the company was seized by Allied forces and placed under French control, the factory was torn down, and its records were destroyed. The former Mauser engineers Edmund Heckler and Theodor Koch, together with their associate Aled Seidel founded Heckler and Koch arms firm in the following years, recovering some leftovers of Mauser company which remained in the arms of Allied forces until 1952 when it was again permitted to continue manufacturing firearms. In the second half of the 20th century, the company presented some new models such as Model 66, Model 77, Model 86SR, Mauser SP66, Models 94 and 96, Mauser SR 97, Mauser 90SA and Mauser 90DA.

The Rheinmetall Berlin AG bought the firearms division of the company in 1996 and renamed it to Mauser-Werke Oberndorf Waffensysteme GmbH. In 1999, part of the Mauser was sold to Schweizerische Industrie Gesellschaft company often referred to as SIG, which later became known as Mauser Jagdwaffen GmbH.

Today, the company is under the parentage of the Blaser Group, which also manufactures rifles under the J.P. Sauer & Sohn brand. Mauser has presented some new models in the last few years, such as Mauser M03, M12, and M18, attesting to the company’s rich and successful history once again.

Mauser K98k (Bulb) Rifle Review

Mauser K98k is a controlled feed bolt-action rifle introduced in 1935 used as a primary infantry rifle of the German army during World War II. K98k was derived from some of the Mauser’s earlier rifles such as Karabiner 98b and Gewehr 98, thus it shares most of the design details with the forerunners. The main change was made in the design of a straight bolt handle which was reshaped and bent, allowing for a faster bolt operation and optics mounting directly on the top of the receiver.

The rifle went through some design changes in the course of the production period as the demand increased during the war and the manufacturers had to find new ways to fulfil the increased number of orders. The pre-war version of K98k came with an included cleaning rod, fitted through a bayonet stud which was banned on later versions. Another change was the stock wood - the early rifles came with a walnut stock whereas the newer ones used laminated wood. Some finesses such as milled steel parts or the removable front sight were replaced by a production-friendlier stamped steel and a fixed sight. The shape of the butt plate was, on the contrary, improved on the newer versions as it was redesigned into a cupped shape increasing the overall durability of the stock which was often chipped or damaged on the early models.

However, there are no changes in the receiver design between the models produced before and during the war. The bolt body features three locking lugs, two at the front and one at the rear end of the bolt that locks up safely with the action's housing. The steel parts are blued protecting the weapon from rust. Positioned at the rear top end of the receiver, there is a standard Mauser flag-type safety lever. A dedicated bolt release lever is placed on the left rear side of the receiver.

The older rifles come with a steel floorplate and an internal five-round capacity magazine that can be loaded using stripper clips, thus the receiver on those models features a bulb that functions as a guiding slot. The modern civilian version of K98k commonly known as Mauser M98 uses a receiver without a bulb, making the mounting surfaces on the rifles different; meaning that they will not fit the same scope mounts.

After the war, the allies and liberated European countries continued the production of K98k using numerous leftover parts and German machinery captured during the war. Despite using the original Mauser design, many of the newly established rifles that derived from the K98k were rebranded e.g., Yugoslavian M48, Spanish M43 or Israeli Mauser.

The possible barrel length for Mauser K98k is 600 mm (23.6-inch).

Mauser K98k chambered for 7.92x57mm Mauser

Figure 1: Mauser K98k chambered for 7.92x57mm Mauser (Source: https://www.highwoodclassicarms.co.uk/Firerms%20For%20Sale/0129.htm)

Mauser K98k can be chambered for the following calibres:

7.92x57mm Mauser
The rifle is available in the following variants:
Mauser K98k Kriegsmodell
Mauser K98k Sniper Variant
Mauser K98k Paratrooper Variant
Mauser K98k G40k
Mauser K98k KKW Cadet Rifle

Mauser K98k receivers come without holes therefore they must be manually drilled by a gunsmith.

Mauser K98k chambered for 7.92x57mm Mauser

Figure 2: The receiver of Mauser K98k, chambered for 7.92x57mm Mauser (Source: https://www.highwoodclassicarms.co.uk/Firerms%20For%20Sale/0129.htm)

A: 22 mm

B: /

C: 13 mm

BHU: 4 mm

Ø: /

R1: R14/30°

R2: R18

The abovementioned data describes the receiver radius together with the height difference between the front and rear mounting surface. The distance between the front and rear surface holes (A & C) is provided based on the Rusan pivot mount that we recommend and is one of the frequently used holes positioning for this rifle.

Please note that the positioning of the holes on the rail and receiver is determined by a gunsmith before drilling and can vary.

Which Rifles Have Interchangeable Mounts

Two-piece mounts

All the rifles listed in the category below have two-piece mounts interchangeable with Mauser K98k Standard. To meet interchangeability conditions, two-piece mounts must match in all dimensions except the B distance. B distance can vary because two-piece mounts can be installed and adjusted closer or further apart. Since the K98k comes without pre-drilled holes on the receiver, the interchangeability conditions mostly depend on BHU which is the difference in height between the front and rear mounting surface and the surface radius. Rifles that meet such criteria are:

Gewehr 98
Zastava M48
Spanish Mauser M43
Israeli Mauser

One-piece mounts

All the rifles listed in the category below have one-piece mounts interchangeable with Mauser K98k. For one-piece mounts to fit on a rifle, mounting surfaces on these rifles must match in every dimension. Rifles that share the same dimensions and mounting surface with Mauser K98k are:

Gewehr 98
Zastava M48
Spanish Mauser M43
Israeli Mauser

*As the K98k comes without holes on the receiver, the interchangeability conditions depend on the overall length and shape of the receiver. Please note that the old versions of Mauser K98k come with a bulb on the receiver which is used for stripper-clip feeding.

The modern civilian version of K98k commonly known as Mauser M98 uses a receiver without a bulb, making the mounting surfaces on the rifles different; meaning that they will not fit the same scope mounts.

Our Recommendations for Mounts

Detachable Repeatable Mounts

Detachable pivot mounts make attaching and detaching your preferred optic an easy task. This pivot mount made by the Croatian company Rusan is repeatable and comes with a ten-year warranty, making it a suitable choice for Mauser K98k.

Picatinny Rails

This Picatinny rail manufactured by the German company EAW is made of steel and will be a suitable fit for Mauser K98k.

The rail comes without holes therefore they must be manually drilled by a gunsmith.

Help Us Build Our Riflescope Mounts Database

If you happen to own this or any other rifle, we would appreciate it if you could help us expand our database by sending us some photos of the rifle receiver (the bare mounting surface of the rifle without the mounts installed). For your help, our company offers a fair return in terms of practical rewards.

Please send us an email for more information. You can contact us here: info@optics-trade.eu

Compatibility Above

Filters

Sort

In stock

Rusan Front Pivot Base for Mauser K98 (Witht Bulb)

Rusan Front Pivot Base for Mauser K98 (With Bulb)

AU$53.45

Add to compare

In stock

EAW Lateral Slide-on Mount for Mauser K 98, 30 mm

AU$808.26

Add to compare

In stock

EAW Lateral Slide-on Mount for Mauser K 98, Picatinny rail

AU$678.68

Add to compare

In stock

Rusan Pivot mount for Mauser K98/M48, Yukon Photon, 30mm, extra high

AU$364.45

Add to compare

In stock

On sale

EAW Lateral Slide-on Mount for Mauser K 98, 26 mm

AU$597.69 AU$792.06

Add to compare

In stock

EAW Roll-off Mounts with foot plates for Mauser K 98, with bulb, 30 mm

As low as AU$500.51

View Product

Add to compare

In stock

Rusan Pivot mount for Mauser K98/ M48, Docter Sight

AU$322.33

Add to compare

In stock

EAW Lateral Slide-on Mount for Mauser K 98, LM rail

AU$808.26

Add to compare

In stock

Rusan Pivot mount for Mauser K98/M48, ATN 4K, one-piece

AU$387.12

Add to compare

In stock

Rusan Pivot mount for Mauser K98/M48, Pard NV008, one-piece

AU$387.12

Add to compare

In stock

Rusan Pivot mount for Mauser K98, M48, Yukon Photon, 30mm, one-piece

Rusan Pivot mount for Mauser K98/M48, Yukon Photon, one-piece

AU$387.12

Add to compare

In stock

Rusan Pivot mount for Mauser K98/M48, Pulsar Digisight/Trail/Apex, one-piece

AU$387.12

Add to compare

Filters

Sort

VIDEO

There are two terms found for similar thing: quick release scope mounts and quick detach scope mounts. Term quick release scope mounts is used mostly in Europe and quick detach scope mounts is used mainly in USA, although they mean the same thing. With these terms we describe a scope mount that can be quickly removed from the rifle in the field without using any tools and quickly attached back on the rifle when needed.

Main advantages:

possibility to use multiple scopes on the rifle,
easy transportation of the scope and the rifle separately,
if scope fails, it is possible to immediately detach it and use iron sights.

FIXED vs DETACHABLE scope mounts

Fixed scope mounts are mounted to the rifle with screws and sometimes even with glue. This means that it is impossible to attach or detach the scope mount using bare hands without using tools. It also means that they are not meant for constantly being attached on or detached off the rifle. Once you screw the mount on the rifle, it normally stays there for a longer period of use.

Detachable scope mounts offer possibility to attach or detach them without using any tools. This is extremely handy while transporting the rifle and the scope separately and it also offers multiple solutions of different optics on the same rifle. Detachable scope mounts can be attached or detached from the rifle in a matter of seconds, using bare hands.

Fixed Mount

Fixed Mount

DETACHABLE vs REPEATABLE scope mounts

It is important to know and understand expressions “detachable” and “repeatable” while talking about scope mounts. Term detachable scope mounts implies scope mounts that can be quickly attached or detached without using any tools. However, when you detach this kind of mount and attach it back on the rifle, it is recommended to zero the rifle before using it again. Procedure of detaching and again attaching the mount will probably need a sighting in before next shooting, because mount will not be secured on the rifle in the perfectly same position and conditions as it was before detaching it off the rifle.

On the contrary, repeatable scope mounts are most sophisticated mounts. These scope mounts are also detachable, however – they provide removing scope from the rifle and attaching it back again without zeroing the rifle every time. This means that they are made more precisely and that they are offering a possibility of using different optical sights / scope on the same rifle. These mounts are ideal for hunters who can use optical and iron sights interchangeably, depending on the needs in different situations. With the repeatable scope mounts, it is useful to keep them oiled as well as the upper part of the rifle, so that repeatability is more ensured. With a touch of oil, the repeatability might be better, because parts of the mount will always return to their previous locations.

Different types of repeatable scope mounts:

Pivot mounts,
Dentler mounts,
Picatinny repeatable mounts,
12 mm dovetail repeatable mounts (for break barrel rifles, such as Steyr Duett, Blaser B750, Fair Combi, Fair SLX 800, Bettinsoli rifles, etc.),
Original repeatable mounts, made by manufacturers of rifles for their rifles (Blaser mount, Sauer SUM mount, Mauser M03 mount, Steyr Monoblock mount, etc.).

Repeatable Mount

Repeatable Mount

TIP OFF / ROLL OFF vs SLIDE ON mounts

Nowadays, there are a whole lot of different possibilities, made for attaching riflescopes on the rifles. There are also a lot of different expressions, having the same meaning. It is good to know that tip off and roll off mounts are basically the same thing. They represent quick release scope mounts for dovetails and rails which can be rolled or tipped off the rail vertically to the side of the rail. On the contrary, there are also slide on mounts available on the market. They represent quick release scope mounts that can be slided on or off the rail or dovetail from front or rear side of the rail / dovetail. All of these expressions are mainly used for separate rings that can be attached to the rails / dovetails. As far as functioning the rifle, it does not matter which one of these mounts you choose – tip / roll off or slide on mounts. If they are installed correctly, they are all going to work. However, the main difference between them is the principle of attaching them on rails on dovetails.

Slide On Mount vs. Roll Off Mount

Slide On Mount vs. Roll Off Mount

Mauser K98k (Bulb)

Sub Categories

About the Mauser

Mauser K98k (Bulb) Rifle Review

Mauser K98k can be chambered for the following calibres: